Engine power: Electric start Briggs and Stratton14 hp. Flow rate: 11 gpm (41 l/min) @ 1700 PSI (120Bar) Two 73 Ft (22 meter) Dash 8m hoses with HTMA flat-face standard couplings.

New engine oil and fuel filter, Removed fuel tank and flushed clean, new battery, replaced oil in hydraulic tank and flushed hydraulic lines with new AW46 Hydraulic oil. Engine runs strong, charging system working.

Flow tested hydraulic power unit under full load (1700 psi) and full rpm (3600) for 10 minutes, oil temperature 160 degrees. The results were 11 GPM (41 L/min) @ 1700 PSI (120Bar).  Test shows 100% flow and pressure for horse power provided.

 This unit is ready for use. This can power a full range of tools, from wall saws and large core drills to small drilling hammers, hydraulic breakers and pumps.  New replacement cost for these types of unit range from $4800 to $6500. Asking $2950.00.

We have gone through this pump inch by inch and fixed every little item on it. Here is a list

 New shoes for the brakes, seals and new wheel bearings.

 New Tires (One had damage on inspection replaced both with new)

All the Trailer lights are operating properly.

New hydraulic oil and return filter plus cleaned tank and suction filters. We also flushed out hydraulic drive cylinders with fresh clean oil.

New engine oil, filter and air filter. Replaced battery, check fuel tank for contamination (NONE).

All control panel functions working with proper safety decals.

New hoppers grate rubbers and pivots

New concrete pistons, wear bands and oil in the water box.

Wear plate and wear ring like new 100% and installed new back up ring for wear ring.

New outlet and shaft seals for S-tube

Checked all greasing points for S-Tube throw cylinder.

Flow test main pump for operation (Excellent)

Removed and serviced alternator and starter.

Checked and cleaned all electrical connections.

Also available with pump spare parts for next service:

                    1 Oil filter

                    1 Fuel Filter

                    1 Proximity switch and fuse set (In control panel not required for service work)

                    2 piston heads

                    1 Hydraulic return filter

We recommend that a regular service on done on the pump and every 350-400 hours after that.

   All of equipment that leaves here has our contact phone number. So you can contact us for any assistance in technical support, service or parts. Canusa Equipment Ltd. 604-526-5151.

- Automatic Pad Clamping Pressure is maintained evenly across the pad. (Extends wear part life). Also, no operator adjustments necessary during operation.

- Dust Suppression System. Keeps unwanted dust out of the atmosphere.

- Smoothest Output. Our precision feed wheel assembly maintains the uniform flow of material into the airstream by supplying constant metered amounts of material. (No high-low surge in material hose).

- High-Quality Concrete. Smooth placement results in even hydration of material at the nozzle and minimal rebound.

- Highly-Portable and Easy to Store. Compact size allows it to be used in even the most confined work areas. Putting a wheel mounted Gun on a truck with 2 scaffold planks is a two man job. Narrow width lets it fit through narrow doors.

- Versatile. Interchangeable Components (hoses and feed wheels) gives you the advantage of controlled rates of feed and a wide range of output.

- Easy to Maintain. Easy access to perfrom on-the-line service with minimum tools.

- Minimum Labor Required to Operate. Only minutes are required to instruct a ready-mix truck driver or shoveler, and from there the gun needs minimal adjustments.

- Gun Disassembles in Minutes. When necessary, the removal of 7 nuts allows the machine to come quickly and completely apart (except the sealed-in drive train).

- Rugged and Reliable. Sealed-in-Oil Gear Drive insures long life. All gears are of spur design and manufactured of heat treated alloy, running in ball or roller bearings. (No chains).

- Safe. Our feed process eliminates dangerous pressure chambers, reduces possible injuries.

- Continuous Operation. Material receiving hopper is open to the atmosphere.

- Easiest Gunite Machine to Understand and Operate.

209 COMPONENT OPTIONS:
(All sizes and configurations do not go together.)

HOPPER: (Flat Hopper with Bag Breaker).
Flat Hopper with Bag Breaker is generally used in refractory applications and with pre-bagged materials.

MOTOR: Air Motor (Rotary Vane Direct Drive): 8AM (5hp)
Air motor will deliver a feed wheel rotation of 50 r.p.m.’s down to 2 r.p.m.’s by throttling the air supply to the motor.
Optional 3hp electric motor drive with adjustable speeds.

FEED BOWLS: (16 pocket, 18 pocket).
More pockets = Smoother Finish, Fewer Pockets = More Output

AIR HOSE / MATERIAL HOSE: We highly recommend using the same size air and material hoses.
Special Gunite Hose or Refractory hose is used for material
Larger aggregates require the larger material hoses in order to prevent hose blockages.

GOOSENECK: (1-1/4″, 1-1/2″).
Liner Type – abrasion resistant liner is replaceable.
Sold Steel – is maintained by hard-facing as wear occurs.

WEAR PAD: Only one wear pad for the 16 pocket and one for the 18 pocket.

MESH SCREEN: (15/16″)(3/4″).
Keeps large aggregate out of the hopper.

BAG BREAKER:Sits on top of the hopper. Used with bagged material.

AGITATOR: Used to agitate the material. Comes with a 2 blade agitator.

OPTIONAL EQUIPMENT:

Vibrator: Assists in feeding material into the pockets.

Skid Mounted: Mainly for underground applications.

Optional Bulk Bag Adapter Used with “Super-sacks” or “Bulk Bags”. Prevents injury and reduces dust.

Maximum theoretical performance shown above. Maximum output and pressure cannot be reached simultaneously. Performance will vary depending on slump, mix design and pipeline diameter. Specifications subject to change without prior notice.

Download REED’s 209 Spec Sheet

- High-Quality Concrete. Smooth placement results in even hydration of material at the nozzle and minimal rebound.

- Highly-Portable and Easy to Store. Compact size allows it to be used in even the most confined work areas. Putting a wheel mounted Gun on a truck with 2 scaffold planks is a two man job. Narrow width lets it fit through narrow doors.

- Versatile. Interchangeable Components (hoses and feed wheels) gives you the advantage of controlled rates of feed and a wide range of output.

- Easy to Maintain. Easy access to perfrom on-the-line service with minimum tools.

- Minimum Labor Required to Operate. Only minutes are required to instruct a ready-mix truck driver or shoveler, and from there the gun needs minimal adjustments.

- Gun Disassembles in Minutes. When necessary, the removal of 7 nuts allows the machine to come quickly and completely apart (except the sealed-in drive train).

- Rugged and Reliable. Sealed-in-Oil Gear Drive insures long life. All gears are of spur design and manufactured of heat treated alloy, running in ball or roller bearings. (No chains).

- Safe. Our feed process eliminates dangerous pressure chambers, reduces possible injuries.

- Continuous Operation. Material receiving hopper is open to the atmosphere.

- Easiest Gunite Machine to Understand and Operate.

SOVA COMPONENT OPTIONS:
(All sizes and configurations do not go together.)

HOPPER: (Flat Hopper with Bag Breaker).
Flat Hopper with Bag Breaker is generally used in refractory applications and with pre-bagged materials.

MOTOR: Air Motor (Rotary Vane Direct Drive): 8AM (5hp)
Air motor will deliver a feed wheel rotation of 50 r.p.m.’s down to 2 r.p.m.’s by throttling the air supply to the motor.

FEED BOWLS: (16 pocket, 18 pocket).
More pockets = Smoother Finish, Fewer Pockets = More Output

AIR HOSE / MATERIAL HOSE: We highly recommend using the same size air and material hoses.
Special Gunite Hose or Refractory hose is used for material
Larger aggregates require the larger material hoses in order to prevent hose blockages.

GOOSENECK: (1-1/4″, 1-1/2″).
Liner Type – abrasion resistant liner is replaceable.
Solid Steel – is maintained by hard-facing as wear occurs.

WEAR PAD: Only one wear pad for the 16 pocket and one for the 18 pocket.

MESH SCREEN: (15/16″)(3/4″).
Keeps large aggregate out of the hopper.

BAG BREAKER: Sits on top of the hopper. Used with bagged material.

AGITATOR: Used to agitate the material. Comes with a 2 blade agitator.

OPTIONAL EQUIPMENT:
Vibrator: Assists in feeding material into the pockets.

Skid Mounted: Mainly for underground applications.

Optional Bulk Bag Adapter Used with “Super-sacks” or “Bulk Bags”. Prevents injury and reduces dust.

Maximum theoretical performance shown above. Maximum output and pressure cannot be reached simultaneously. Performance will vary depending on slump, mix design and pipeline diameter. Specifications subject to change without prior notice.

Download REED’s Sova Spec Sheet

- Automatic Pad Clamping Pressure is maintained evenly across the pad. (Extends wear part life). Also, no operator adjustments necessary during operation.

- Dust Suppression System. Keeps unwanted dust out of the atmosphere.

- Smoothest Output. Our precision feed wheel assembly maintains the uniform flow of material into the airstream by supplying constant metered amounts of material. (No high-low surge in material hose).

- High-Quality Concrete. Smooth placement results in even hydration of material at the nozzle and minimal rebound.

- Highly-Portable and Easy to Store. Compact size allows it to be used in even the most confined work areas. Putting a wheel mounted Gun on a truck with 2 scaffold planks is a two man job. Narrow width lets it fit through narrow doors.

- Versatile. Interchangeable Components (hoses and feed wheels) gives you the advantage of controlled rates of feed and a wide range of output.

- Easy to Maintain. Easy access to perfrom on-the-line service with minimum tools.

- Minimum Labor Required to Operate. Only minutes are required to instruct a ready-mix truck driver or shoveler, and from there the gun needs minimal adjustments.

- Gun Disassembles in Minutes. When necessary, the removal of 7 nuts allows the machine to come quickly and completely apart (except the sealed-in drive train).

- Rugged and Reliable. Sealed-in-Oil Gear Drive insures long life. All gears are of spur design and manufactured of heat treated alloy, running in ball or roller bearings. (No chains).

- Safe. Our feed process eliminates dangerous pressure chambers, reduces possible injuries.

- Continuous Operation. Material receiving hopper is open to the atmosphere.

- Easiest Gunite Machine to Understand and Operate.

209 COMPONENT OPTIONS:
(All sizes and configurations do not go together.)

HOPPER: (Flat Hopper with Bag Breaker).
Flat Hopper with Bag Breaker is generally used in refractory applications and with pre-bagged materials.

MOTOR: Air Motor (Rotary Vane Direct Drive): 8AM (5hp)
Air motor will deliver a feed wheel rotation of 50 r.p.m.’s down to 2 r.p.m.’s by throttling the air supply to the motor.
Optional 3hp electric motor drive with adjustable speeds.

FEED BOWLS: (16 pocket, 18 pocket).
More pockets = Smoother Finish, Fewer Pockets = More Output

AIR HOSE / MATERIAL HOSE: We highly recommend using the same size air and material hoses.
Special Gunite Hose or Refractory hose is used for material
Larger aggregates require the larger material hoses in order to prevent hose blockages.

GOOSENECK: (1-1/4″, 1-1/2″).
Liner Type – abrasion resistant liner is replaceable.
Sold Steel – is maintained by hard-facing as wear occurs.

WEAR PAD: Only one wear pad for the 16 pocket and one for the 18 pocket.

MESH SCREEN: (15/16″)(3/4″).
Keeps large aggregate out of the hopper.

BAG BREAKER:Sits on top of the hopper. Used with bagged material.

AGITATOR: Used to agitate the material. Comes with a 2 blade agitator.

OPTIONAL EQUIPMENT:

Vibrator: Assists in feeding material into the pockets.

Skid Mounted: Mainly for underground applications.

Optional Bulk Bag Adapter Used with “Super-sacks” or “Bulk Bags”. Prevents injury and reduces dust.

Maximum theoretical performance shown above. Maximum output and pressure cannot be reached simultaneously. Performance will vary depending on slump, mix design and pipeline diameter. Specifications subject to change without prior notice.

Download REED’s Lova Spec Sheet

- High Performance; pressures up to 2,000 psi
- Smooth-running “Closed-Loop” hydraulics
- Solid-state “Black Box” cycling; the fastest responding system made to minimize surge
- Twin-shift cylinders; for fast, even shifting
- Low hopper height; easy fill from old-style mixer trucks.
- Adjustable shifting-force valve; lets you increase force for harsh-mixes and decrease force during clean-out. Only REED pumps have it.
- The strongest trailer in the industry; there is 18″ of steel between the engine and axle.
- Dual 4500 lb. axles; provides the most durability possible
- Harsh Mix Hopper; for tough mixes (Optional)
- We can truck mount it! Ask up for more details. (Optional)
- REED “1-3-2 Warranty”: Covers parts for one year, structural for three years, and the Black Box for two years

Maximum theoretical performance shown above. Maximum output and pressure cannot be reached simultaneously. Performance will vary depending on slump, mix design and pipeline diameter. Specifications subject to change without prior notice.

Download REED’s C-Series Spec Sheet

- Solid-state “Black Box” cycling; the fastest responding system made to minimize surge.

- Low hopper height; easy fill from old-style mixer trucks

- Adjustable shifting-force valve; lets you increase force for harsh-mixes and decrease force during clean-out. Only REED pumps have it.

- 9000lb. axle capacity; strongest axle in the industry in this class of pump.

- Harsh mix hopper (Optional)

- We can truck mount it! Ask up for more details. (Optional)

- REED “1-3-2 Warranty”: Covers parts for one year, structural for three years, and the Black Box for two years

Maximum theoretical performance shown above. Maximum output and pressure cannot be reached simultaneously. Performance will vary depending on slump, mix design and pipeline diameter. Specifications subject to change without prior notice.

Download REED’s B-Series Spec Sheet